Mac Easy 2010 May/Mac Life Ubuntu.iso/casper/filesystem.squashfs/usr/src/linux-headers-2.6.28-15/drivers/net/Kconfig

Text File | 2009-09-09 | 100.3 KB | 3,060 lines

#
# Network device configuration
#

menuconfig NETDEVICES
    default y if UML
    depends on NET
    bool "Network device support"
    ---help---
      You can say N here if you don't intend to connect your Linux box to
      any other computer at all.

      You'll have to say Y if your computer contains a network card that
      you want to use under Linux. If you are going to run SLIP or PPP over
      telephone line or null modem cable you need say Y here. Connecting
      two machines with parallel ports using PLIP needs this, as well as
      AX.25/KISS for sending Internet traffic over amateur radio links.

      See also "The Linux Network Administrator's Guide" by Olaf Kirch and
      Terry Dawson. Available at <http://www.tldp.org/guides.html>.

      If unsure, say Y.

# All the following symbols are dependent on NETDEVICES - do not repeat
# that for each of the symbols.
if NETDEVICES

config IFB
    tristate "Intermediate Functional Block support"
    depends on NET_CLS_ACT
    ---help---
      This is an intermediate driver that allows sharing of
      resources.
      To compile this driver as a module, choose M here: the module
      will be called ifb.  If you want to use more than one ifb
      device at a time, you need to compile this driver as a module.
      Instead of 'ifb', the devices will then be called 'ifb0',
      'ifb1' etc.
      Look at the iproute2 documentation directory for usage etc

config DUMMY
    tristate "Dummy net driver support"
    ---help---
      This is essentially a bit-bucket device (i.e. traffic you send to
      this device is consigned into oblivion) with a configurable IP
      address. It is most commonly used in order to make your currently
      inactive SLIP address seem like a real address for local programs.
      If you use SLIP or PPP, you might want to say Y here. Since this
      thing often comes in handy, the default is Y. It won't enlarge your
      kernel either. What a deal. Read about it in the Network
      Administrator's Guide, available from
      <http://www.tldp.org/docs.html#guide>.

      To compile this driver as a module, choose M here: the module
      will be called dummy.  If you want to use more than one dummy
      device at a time, you need to compile this driver as a module.
      Instead of 'dummy', the devices will then be called 'dummy0',
      'dummy1' etc.

config BONDING
    tristate "Bonding driver support"
    depends on INET
    ---help---
      Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
      Channels together. This is called 'Etherchannel' by Cisco,
      'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.

      The driver supports multiple bonding modes to allow for both high
      performance and high availability operation.

      Refer to <file:Documentation/networking/bonding.txt> for more
      information.

      To compile this driver as a module, choose M here: the module
      will be called bonding.

config MACVLAN
    tristate "MAC-VLAN support (EXPERIMENTAL)"
    depends on EXPERIMENTAL
    ---help---
      This allows one to create virtual interfaces that map packets to
      or from specific MAC addresses to a particular interface.

      Macvlan devices can be added using the "ip" command from the
      iproute2 package starting with the iproute2-2.6.23 release:

      "ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan"

      To compile this driver as a module, choose M here: the module
      will be called macvlan.

config EQUALIZER
    tristate "EQL (serial line load balancing) support"
    ---help---
      If you have two serial connections to some other computer (this
      usually requires two modems and two telephone lines) and you use
      SLIP (the protocol for sending Internet traffic over telephone
      lines) or PPP (a better SLIP) on them, you can make them behave like
      one double speed connection using this driver.  Naturally, this has
      to be supported at the other end as well, either with a similar EQL
      Linux driver or with a Livingston Portmaster 2e.

      Say Y if you want this and read
      <file:Documentation/networking/eql.txt>.  You may also want to read
      section 6.2 of the NET-3-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here: the module
      will be called eql.  If unsure, say N.

config TUN
    tristate "Universal TUN/TAP device driver support"
    select CRC32
    ---help---
      TUN/TAP provides packet reception and transmission for user space
      programs.  It can be viewed as a simple Point-to-Point or Ethernet
      device, which instead of receiving packets from a physical media,
      receives them from user space program and instead of sending packets
      via physical media writes them to the user space program.

      When a program opens /dev/net/tun, driver creates and registers
      corresponding net device tunX or tapX.  After a program closed above
      devices, driver will automatically delete tunXX or tapXX device and
      all routes corresponding to it.

      Please read <file:Documentation/networking/tuntap.txt> for more
      information.

      To compile this driver as a module, choose M here: the module
      will be called tun.

      If you don't know what to use this for, you don't need it.

config VETH
    tristate "Virtual ethernet pair device"
    ---help---
      This device is a local ethernet tunnel. Devices are created in pairs.
      When one end receives the packet it appears on its pair and vice
      versa.

config NET_SB1000
    tristate "General Instruments Surfboard 1000"
    depends on PNP
    ---help---
      This is a driver for the General Instrument (also known as
      NextLevel) SURFboard 1000 internal
      cable modem. This is an ISA card which is used by a number of cable
      TV companies to provide cable modem access. It's a one-way
      downstream-only cable modem, meaning that your upstream net link is
      provided by your regular phone modem.

      At present this driver only compiles as a module, so say M here if
      you have this card. The module will be called sb1000. Then read
      <file:Documentation/networking/README.sb1000> for information on how
      to use this module, as it needs special ppp scripts for establishing
      a connection. Further documentation and the necessary scripts can be
      found at:

      <http://www.jacksonville.net/~fventuri/>
      <http://home.adelphia.net/~siglercm/sb1000.html>
      <http://linuxpower.cx/~cable/>

      If you don't have this card, of course say N.

source "drivers/net/arcnet/Kconfig"

source "drivers/net/phy/Kconfig"

#
#    Ethernet
#

menuconfig NET_ETHERNET
    bool "Ethernet (10 or 100Mbit)"
    depends on !UML
    ---help---
      Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
      type of Local Area Network (LAN) in universities and companies.

      Common varieties of Ethernet are: 10BASE-2 or Thinnet (10 Mbps over
      coaxial cable, linking computers in a chain), 10BASE-T or twisted
      pair (10 Mbps over twisted pair cable, linking computers to central
      hubs), 10BASE-F (10 Mbps over optical fiber links, using hubs),
      100BASE-TX (100 Mbps over two twisted pair cables, using hubs),
      100BASE-T4 (100 Mbps over 4 standard voice-grade twisted pair
      cables, using hubs), 100BASE-FX (100 Mbps over optical fiber links)
      [the 100BASE varieties are also known as Fast Ethernet], and Gigabit
      Ethernet (1 Gbps over optical fiber or short copper links).

      If your Linux machine will be connected to an Ethernet and you have
      an Ethernet network interface card (NIC) installed in your computer,
      say Y here and read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>. You will then also have
      to say Y to the driver for your particular NIC.

      Note that the answer to this question won't directly affect the
      kernel: saying N will just cause the configurator to skip all
      the questions about Ethernet network cards. If unsure, say N.

if NET_ETHERNET

config MII
    tristate "Generic Media Independent Interface device support"
    help
      Most ethernet controllers have MII transceiver either as an external
      or internal device.  It is safe to say Y or M here even if your
      ethernet card lack MII.

config MACB
    tristate "Atmel MACB support"
    depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91CAP9
    select PHYLIB
    help
      The Atmel MACB ethernet interface is found on many AT32 and AT91
      parts. Say Y to include support for the MACB chip.

      To compile this driver as a module, choose M here: the module
      will be called macb.

source "drivers/net/arm/Kconfig"

config AX88796
    tristate "ASIX AX88796 NE2000 clone support"
    depends on ARM || MIPS || SUPERH
    select CRC32
    select MII
    help
      AX88796 driver, using platform bus to provide
      chip detection and resources

config AX88796_93CX6
    bool "ASIX AX88796 external 93CX6 eeprom support"
    depends on AX88796
    select EEPROM_93CX6
    help
      Select this if your platform comes with an external 93CX6 eeprom.

config MACE
    tristate "MACE (Power Mac ethernet) support"
    depends on PPC_PMAC && PPC32
    select CRC32
    help
      Power Macintoshes and clones with Ethernet built-in on the
      motherboard will usually use a MACE (Medium Access Control for
      Ethernet) interface. Say Y to include support for the MACE chip.

      To compile this driver as a module, choose M here: the module
      will be called mace.

config MACE_AAUI_PORT
    bool "Use AAUI port instead of TP by default"
    depends on MACE
    help
      Some Apple machines (notably the Apple Network Server) which use the
      MACE ethernet chip have an Apple AUI port (small 15-pin connector),
      instead of an 8-pin RJ45 connector for twisted-pair ethernet.  Say
      Y here if you have such a machine.  If unsure, say N.
      The driver will default to AAUI on ANS anyway, and if you use it as
      a module, you can provide the port_aaui=0|1 to force the driver.

config BMAC
    tristate "BMAC (G3 ethernet) support"
    depends on PPC_PMAC && PPC32
    select CRC32
    help
      Say Y for support of BMAC Ethernet interfaces. These are used on G3
      computers.

      To compile this driver as a module, choose M here: the module
      will be called bmac.

config ARIADNE
    tristate "Ariadne support"
    depends on ZORRO
    help
      If you have a Village Tronic Ariadne Ethernet adapter, say Y.
      Otherwise, say N.

      To compile this driver as a module, choose M here: the module
      will be called ariadne.

config A2065
    tristate "A2065 support"
    depends on ZORRO
    select CRC32
    help
      If you have a Commodore A2065 Ethernet adapter, say Y. Otherwise,
      say N.

      To compile this driver as a module, choose M here: the module
      will be called a2065.

config HYDRA
    tristate "Hydra support"
    depends on ZORRO
    select CRC32
    help
      If you have a Hydra Ethernet adapter, say Y. Otherwise, say N.

      To compile this driver as a module, choose M here: the module
      will be called hydra.

config ZORRO8390
    tristate "Zorro NS8390-based Ethernet support"
    depends on ZORRO
    select CRC32
    help
      This driver is for Zorro Ethernet cards using an NS8390-compatible
      chipset, like the Village Tronic Ariadne II and the Individual
      Computers X-Surf Ethernet cards. If you have such a card, say Y.
      Otherwise, say N.

      To compile this driver as a module, choose M here: the module
      will be called zorro8390.

config APNE
    tristate "PCMCIA NE2000 support"
    depends on AMIGA_PCMCIA
    select CRC32
    help
      If you have a PCMCIA NE2000 compatible adapter, say Y.  Otherwise,
      say N.

      To compile this driver as a module, choose M here: the module
      will be called apne.

config MAC8390
    bool "Macintosh NS 8390 based ethernet cards"
    depends on MAC
    select CRC32
    help
      If you want to include a driver to support Nubus or LC-PDS
      Ethernet cards using an NS8390 chipset or its equivalent, say Y
      and read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

config MAC89x0
    tristate "Macintosh CS89x0 based ethernet cards"
    depends on MAC
    ---help---
      Support for CS89x0 chipset based Ethernet cards.  If you have a
      Nubus or LC-PDS network (Ethernet) card of this type, say Y and
      read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. This module will
      be called mac89x0.

config MACSONIC
    tristate "Macintosh SONIC based ethernet (onboard, NuBus, LC, CS)"
    depends on MAC
    ---help---
      Support for NatSemi SONIC based Ethernet devices.  This includes
      the onboard Ethernet in many Quadras as well as some LC-PDS,
      a few Nubus and all known Comm Slot Ethernet cards.  If you have
      one of these say Y and read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. This module will
      be called macsonic.

config MACMACE
    bool "Macintosh (AV) onboard MACE ethernet"
    depends on MAC
    select CRC32
    help
      Support for the onboard AMD 79C940 MACE Ethernet controller used in
      the 660AV and 840AV Macintosh.  If you have one of these Macintoshes
      say Y and read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

config MVME147_NET
    tristate "MVME147 (Lance) Ethernet support"
    depends on MVME147
    select CRC32
    help
      Support for the on-board Ethernet interface on the Motorola MVME147
      single-board computer.  Say Y here to include the
      driver for this chip in your kernel.
      To compile this driver as a module, choose M here.

config MVME16x_NET
    tristate "MVME16x Ethernet support"
    depends on MVME16x
    help
      This is the driver for the Ethernet interface on the Motorola
      MVME162, 166, 167, 172 and 177 boards.  Say Y here to include the
      driver for this chip in your kernel.
      To compile this driver as a module, choose M here.

config BVME6000_NET
    tristate "BVME6000 Ethernet support"
    depends on BVME6000
    help
      This is the driver for the Ethernet interface on BVME4000 and
      BVME6000 VME boards.  Say Y here to include the driver for this chip
      in your kernel.
      To compile this driver as a module, choose M here.

config ATARILANCE
    tristate "Atari Lance support"
    depends on ATARI
    help
      Say Y to include support for several Atari Ethernet adapters based
      on the AMD Lance chipset: RieblCard (with or without battery), or
      PAMCard VME (also the version by Rhotron, with different addresses).

config SUN3LANCE
    tristate "Sun3/Sun3x on-board LANCE support"
    depends on SUN3 || SUN3X
    help
      Most Sun3 and Sun3x motherboards (including the 3/50, 3/60 and 3/80)
      featured an AMD Lance 10Mbit Ethernet controller on board; say Y
      here to compile in the Linux driver for this and enable Ethernet.
      General Linux information on the Sun 3 and 3x series (now
      discontinued) is at
      <http://www.angelfire.com/ca2/tech68k/sun3.html>.

      If you're not building a kernel for a Sun 3, say N.

config SUN3_82586
    bool "Sun3 on-board Intel 82586 support"
    depends on SUN3
    help
      This driver enables support for the on-board Intel 82586 based
      Ethernet adapter found on Sun 3/1xx and 3/2xx motherboards.  Note
      that this driver does not support 82586-based adapters on additional
      VME boards.

config HPLANCE
    bool "HP on-board LANCE support"
    depends on DIO
    select CRC32
    help
      If you want to use the builtin "LANCE" Ethernet controller on an
      HP300 machine, say Y here.

config LASI_82596
    tristate "Lasi ethernet"
    depends on GSC
    help
      Say Y here to support the builtin Intel 82596 ethernet controller
      found in Hewlett-Packard PA-RISC machines with 10Mbit ethernet.

config SNI_82596
    tristate "SNI RM ethernet"
    depends on NET_ETHERNET && SNI_RM
    help
      Say Y here to support the on-board Intel 82596 ethernet controller
      built into SNI RM machines.

config KORINA
    tristate "Korina (IDT RC32434) Ethernet support"
    depends on NET_ETHERNET && MIKROTIK_RB532
    help
      If you have a Mikrotik RouterBoard 500 or IDT RC32434
      based system say Y. Otherwise say N.

config MIPS_JAZZ_SONIC
    tristate "MIPS JAZZ onboard SONIC Ethernet support"
    depends on MACH_JAZZ
    help
      This is the driver for the onboard card of MIPS Magnum 4000,
      Acer PICA, Olivetti M700-10 and a few other identical OEM systems.

config XTENSA_XT2000_SONIC
    tristate "Xtensa XT2000 onboard SONIC Ethernet support"
    depends on XTENSA_PLATFORM_XT2000
    help
      This is the driver for the onboard card of the Xtensa XT2000 board.

config MIPS_AU1X00_ENET
    bool "MIPS AU1000 Ethernet support"
    depends on SOC_AU1X00
    select PHYLIB
    select CRC32
    help
      If you have an Alchemy Semi AU1X00 based system
      say Y.  Otherwise, say N.

config SGI_IOC3_ETH
    bool "SGI IOC3 Ethernet"
    depends on PCI && SGI_IP27
    select CRC32
    select MII
    help
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

config MIPS_SIM_NET
    tristate "MIPS simulator Network device"
    depends on MIPS_SIM
    help
      The MIPSNET device is a simple Ethernet network device which is
      emulated by the MIPS Simulator.
      If you are not using a MIPSsim or are unsure, say N.

config SGI_O2MACE_ETH
    tristate "SGI O2 MACE Fast Ethernet support"
    depends on SGI_IP32=y

config STNIC
    tristate "National DP83902AV  support"
    depends on SUPERH
    select CRC32
    help
      Support for cards based on the National Semiconductor DP83902AV
      ST-NIC Serial Network Interface Controller for Twisted Pair.  This
      is a 10Mbit/sec Ethernet controller.  Product overview and specs at
      <http://www.national.com/pf/DP/DP83902A.html>.

      If unsure, say N.

config SH_ETH
    tristate "Renesas SuperH Ethernet support"
    depends on SUPERH && \
        (CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712 || CPU_SUBTYPE_SH7763 || \
         CPU_SUBTYPE_SH7619)
    select CRC32
    select MII
    select MDIO_BITBANG
    select PHYLIB
    help
      Renesas SuperH Ethernet device driver.
      This driver support SH7710, SH7712, SH7763 and SH7619.

config SUNLANCE
    tristate "Sun LANCE support"
    depends on SBUS
    select CRC32
    help
      This driver supports the "le" interface present on all 32-bit Sparc
      systems, on some older Ultra systems and as an Sbus option.  These
      cards are based on the AMD Lance chipset, which is better known
      via the NE2100 cards.

      To compile this driver as a module, choose M here: the module
      will be called sunlance.

config HAPPYMEAL
    tristate "Sun Happy Meal 10/100baseT support"
    depends on SBUS || PCI
    select CRC32
    help
      This driver supports the "hme" interface present on most Ultra
      systems and as an option on older Sbus systems. This driver supports
      both PCI and Sbus devices. This driver also supports the "qfe" quad
      100baseT device available in both PCI and Sbus configurations.

      To compile this driver as a module, choose M here: the module
      will be called sunhme.

config SUNBMAC
    tristate "Sun BigMAC 10/100baseT support (EXPERIMENTAL)"
    depends on SBUS && EXPERIMENTAL
    select CRC32
    help
      This driver supports the "be" interface available as an Sbus option.
      This is Sun's older 100baseT Ethernet device.

      To compile this driver as a module, choose M here: the module
      will be called sunbmac.

config SUNQE
    tristate "Sun QuadEthernet support"
    depends on SBUS
    select CRC32
    help
      This driver supports the "qe" 10baseT Ethernet device, available as
      an Sbus option. Note that this is not the same as Quad FastEthernet
      "qfe" which is supported by the Happy Meal driver instead.

      To compile this driver as a module, choose M here: the module
      will be called sunqe.

config SUNGEM
    tristate "Sun GEM support"
    depends on PCI
    select CRC32
    help
      Support for the Sun GEM chip, aka Sun GigabitEthernet/P 2.0.  See also
      <http://www.sun.com/products-n-solutions/hardware/docs/pdf/806-3985-10.pdf>.

config CASSINI
    tristate "Sun Cassini support"
    depends on PCI
    select CRC32
    help
      Support for the Sun Cassini chip, aka Sun GigaSwift Ethernet. See also
      <http://www.sun.com/products-n-solutions/hardware/docs/pdf/817-4341-10.pdf>

config SUNVNET
    tristate "Sun Virtual Network support"
    depends on SUN_LDOMS
    help
      Support for virtual network devices under Sun Logical Domains.

config NET_VENDOR_3COM
    bool "3COM cards"
    depends on ISA || EISA || MCA || PCI
    help
      If you have a network (Ethernet) card belonging to this class, say Y
      and read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      Note that the answer to this question doesn't directly affect the
      kernel: saying N will just cause the configurator to skip all
      the questions about 3COM cards. If you say Y, you will be asked for
      your specific card in the following questions.

config EL1
    tristate "3c501 \"EtherLink\" support"
    depends on NET_VENDOR_3COM && ISA
    ---help---
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.  Also, consider buying a
      new card, since the 3c501 is slow, broken, and obsolete: you will
      have problems.  Some people suggest to ping ("man ping") a nearby
      machine every minute ("man cron") when using this card.

      To compile this driver as a module, choose M here. The module
      will be called 3c501.

config EL2
    tristate "3c503 \"EtherLink II\" support"
    depends on NET_VENDOR_3COM && ISA
    select CRC32
    help
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called 3c503.

config ELPLUS
    tristate "3c505 \"EtherLink Plus\" support"
    depends on NET_VENDOR_3COM && ISA && ISA_DMA_API
    ---help---
      Information about this network (Ethernet) card can be found in
      <file:Documentation/networking/3c505.txt>.  If you have a card of
      this type, say Y and read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called 3c505.

config EL16
    tristate "3c507 \"EtherLink 16\" support (EXPERIMENTAL)"
    depends on NET_VENDOR_3COM && ISA && EXPERIMENTAL
    help
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called 3c507.

config EL3
    tristate "3c509/3c529 (MCA)/3c579 \"EtherLink III\" support"
    depends on NET_VENDOR_3COM && (ISA || EISA || MCA)
    ---help---
      If you have a network (Ethernet) card belonging to the 3Com
      EtherLinkIII series, say Y and read the Ethernet-HOWTO, available
      from <http://www.tldp.org/docs.html#howto>.

      If your card is not working you may need to use the DOS
      setup disk to disable Plug & Play mode, and to select the default
      media type.

      To compile this driver as a module, choose M here. The module
      will be called 3c509.

config 3C515
    tristate "3c515 ISA \"Fast EtherLink\""
    depends on NET_VENDOR_3COM && (ISA || EISA) && ISA_DMA_API
    help
      If you have a 3Com ISA EtherLink XL "Corkscrew" 3c515 Fast Ethernet
      network card, say Y and read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called 3c515.

config ELMC
    tristate "3c523 \"EtherLink/MC\" support"
    depends on NET_VENDOR_3COM && MCA_LEGACY
    help
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called 3c523.

config ELMC_II
    tristate "3c527 \"EtherLink/MC 32\" support (EXPERIMENTAL)"
    depends on NET_VENDOR_3COM && MCA && MCA_LEGACY
    help
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called 3c527.

config VORTEX
    tristate "3c590/3c900 series (592/595/597) \"Vortex/Boomerang\" support"
    depends on NET_VENDOR_3COM && (PCI || EISA)
    select MII
    ---help---
      This option enables driver support for a large number of 10Mbps and
      10/100Mbps EISA, PCI and PCMCIA 3Com network cards:

      "Vortex"    (Fast EtherLink 3c590/3c592/3c595/3c597) EISA and PCI
      "Boomerang" (EtherLink XL 3c900 or 3c905)            PCI
      "Cyclone"   (3c540/3c900/3c905/3c980/3c575/3c656)    PCI and Cardbus
      "Tornado"   (3c905)                                  PCI
      "Hurricane" (3c555/3cSOHO)                           PCI

      If you have such a card, say Y and read the Ethernet-HOWTO,
      available from <http://www.tldp.org/docs.html#howto>. More
      specific information is in
      <file:Documentation/networking/vortex.txt> and in the comments at
      the beginning of <file:drivers/net/3c59x.c>.

      To compile this support as a module, choose M here.

config TYPHOON
    tristate "3cr990 series \"Typhoon\" support"
    depends on NET_VENDOR_3COM && PCI
    select CRC32
    ---help---
      This option enables driver support for the 3cr990 series of cards:

      3C990-TX, 3CR990-TX-95, 3CR990-TX-97, 3CR990-FX-95, 3CR990-FX-97,
      3CR990SVR, 3CR990SVR95, 3CR990SVR97, 3CR990-FX-95 Server,
      3CR990-FX-97 Server, 3C990B-TX-M, 3C990BSVR

      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called typhoon.

config LANCE
    tristate "AMD LANCE and PCnet (AT1500 and NE2100) support"
    depends on ISA && ISA_DMA_API
    help
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>. Some LinkSys cards are
      of this type.

      To compile this driver as a module, choose M here: the module
      will be called lance.  This is recommended.

config NET_VENDOR_SMC
    bool "Western Digital/SMC cards"
    depends on ISA || MCA || EISA || MAC
    help
      If you have a network (Ethernet) card belonging to this class, say Y
      and read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      Note that the answer to this question doesn't directly affect the
      kernel: saying N will just cause the configurator to skip all
      the questions about Western Digital cards. If you say Y, you will be
      asked for your specific card in the following questions.

config WD80x3
    tristate "WD80*3 support"
    depends on NET_VENDOR_SMC && ISA
    select CRC32
    help
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called wd.

config ULTRAMCA
    tristate "SMC Ultra MCA support"
    depends on NET_VENDOR_SMC && MCA
    select CRC32
    help
      If you have a network (Ethernet) card of this type and are running
      an MCA based system (PS/2), say Y and read the Ethernet-HOWTO,
      available from <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called smc-mca.

config ULTRA
    tristate "SMC Ultra support"
    depends on NET_VENDOR_SMC && ISA
    select CRC32
    ---help---
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      Important: There have been many reports that, with some motherboards
      mixing an SMC Ultra and an Adaptec AHA154x SCSI card (or compatible,
      such as some BusLogic models) causes corruption problems with many
      operating systems. The Linux smc-ultra driver has a work-around for
      this but keep it in mind if you have such a SCSI card and have
      problems.

      To compile this driver as a module, choose M here. The module
      will be called smc-ultra.

config ULTRA32
    tristate "SMC Ultra32 EISA support"
    depends on NET_VENDOR_SMC && EISA
    select CRC32
    help
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called smc-ultra32.

config BFIN_MAC
    tristate "Blackfin on-chip MAC support"
    depends on NET_ETHERNET && (BF526 || BF527 || BF536 || BF537)
    select CRC32
    select MII
    select PHYLIB
    select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE
    help
      This is the driver for Blackfin on-chip mac device. Say Y if you want it
      compiled into the kernel. This driver is also available as a module
      ( = code which can be inserted in and removed from the running kernel
      whenever you want). The module will be called bfin_mac.

config BFIN_MAC_USE_L1
    bool "Use L1 memory for rx/tx packets"
    depends on BFIN_MAC && (BF527 || BF537)
    default y
    help
      To get maximum network performance, you should use L1 memory as rx/tx buffers.
      Say N here if you want to reserve L1 memory for other uses.

config BFIN_TX_DESC_NUM
    int "Number of transmit buffer packets"
    depends on BFIN_MAC
    range 6 10 if BFIN_MAC_USE_L1
    range 10 100
    default "10"
    help
      Set the number of buffer packets used in driver.

config BFIN_RX_DESC_NUM
    int "Number of receive buffer packets"
    depends on BFIN_MAC
    range 20 100 if BFIN_MAC_USE_L1
    range 20 800
    default "20"
    help
      Set the number of buffer packets used in driver.

config BFIN_MAC_RMII
    bool "RMII PHY Interface (EXPERIMENTAL)"
    depends on BFIN_MAC && EXPERIMENTAL
    default y if BFIN527_EZKIT
    default n if BFIN537_STAMP
    help
      Use Reduced PHY MII Interface

config SMC9194
    tristate "SMC 9194 support"
    depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN)
    select CRC32
    ---help---
      This is support for the SMC9xxx based Ethernet cards. Choose this
      option if you have a DELL laptop with the docking station, or
      another SMC9192/9194 based chipset.  Say Y if you want it compiled
      into the kernel, and read the file
      <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO,
      available from <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called smc9194.

config SMC91X
    tristate "SMC 91C9x/91C1xxx support"
    select CRC32
    select MII
    depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || \
        MIPS || BLACKFIN || MN10300
    help
      This is a driver for SMC's 91x series of Ethernet chipsets,
      including the SMC91C94 and the SMC91C111. Say Y if you want it
      compiled into the kernel, and read the file
      <file:Documentation/networking/smc9.txt>  and the Ethernet-HOWTO,
      available from  <http://www.linuxdoc.org/docs.html#howto>.

      This driver is also available as a module ( = code which can be
      inserted in and removed from the running kernel whenever you want).
      The module will be called smc91x.  If you want to compile it as a
      module, say M here and read <file:Documentation/kbuild/modules.txt>.

config NET_NETX
    tristate "NetX Ethernet support"
    select MII
    depends on ARCH_NETX
    help
      This is support for the Hilscher netX builtin Ethernet ports

      To compile this driver as a module, choose M here. The module
      will be called netx-eth.

config DM9000
    tristate "DM9000 support"
    depends on ARM || BLACKFIN || MIPS
    select CRC32
    select MII
    ---help---
      Support for DM9000 chipset.

      To compile this driver as a module, choose M here.  The module
      will be called dm9000.

config DM9000_DEBUGLEVEL
    int "DM9000 maximum debug level"
    depends on DM9000
    default 4
    help
      The maximum level of debugging code compiled into the DM9000
      driver.

config DM9000_FORCE_SIMPLE_PHY_POLL
    bool "Force simple NSR based PHY polling"
    depends on DM9000
    ---help---
      This configuration forces the DM9000 to use the NSR's LinkStatus
      bit to determine if the link is up or down instead of the more
      costly MII PHY reads. Note, this will not work if the chip is
      operating with an external PHY.

config ENC28J60
    tristate "ENC28J60 support"
    depends on EXPERIMENTAL && SPI && NET_ETHERNET
    select CRC32
    ---help---
      Support for the Microchip EN28J60 ethernet chip.

      To compile this driver as a module, choose M here. The module will be
      called enc28j60.

config ENC28J60_WRITEVERIFY
    bool "Enable write verify"
    depends on ENC28J60
    ---help---
      Enable the verify after the buffer write useful for debugging purpose.
      If unsure, say N.

config SMC911X
    tristate "SMSC LAN911[5678] support"
    select CRC32
    select MII
    depends on ARM || SUPERH
    help
      This is a driver for SMSC's LAN911x series of Ethernet chipsets
      including the new LAN9115, LAN9116, LAN9117, and LAN9118.
      Say Y if you want it compiled into the kernel,
      and read the Ethernet-HOWTO, available from
      <http://www.linuxdoc.org/docs.html#howto>.

      This driver is also available as a module. The module will be
      called smc911x.  If you want to compile it as a module, say M
      here and read <file:Documentation/kbuild/modules.txt>

config SMSC911X
    tristate "SMSC LAN911x/LAN921x families embedded ethernet support"
    depends on NET_ETHERNET
    select CRC32
    select MII
    ---help---
      Say Y here if you want support for SMSC LAN911x and LAN921x families
      of ethernet controllers.
      To compile this driver as a module, choose M here and read
      <file:Documentation/networking/net-modules.txt>. The module
      will be called smsc911x.

config NET_VENDOR_RACAL
    bool "Racal-Interlan (Micom) NI cards"
    depends on ISA
    help
      If you have a network (Ethernet) card belonging to this class, such
      as the NI5010, NI5210 or NI6210, say Y and read the Ethernet-HOWTO,
      available from <http://www.tldp.org/docs.html#howto>.

      Note that the answer to this question doesn't directly affect the
      kernel: saying N will just cause the configurator to skip all
      the questions about NI cards. If you say Y, you will be asked for
      your specific card in the following questions.

config NI5010
    tristate "NI5010 support (EXPERIMENTAL)"
    depends on NET_VENDOR_RACAL && ISA && EXPERIMENTAL && BROKEN_ON_SMP
    ---help---
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>. Note that this is still
      experimental code.

      To compile this driver as a module, choose M here. The module
      will be called ni5010.

config NI52
    tristate "NI5210 support"
    depends on NET_VENDOR_RACAL && ISA
    help
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called ni52.

config NI65
    tristate "NI6510 support"
    depends on NET_VENDOR_RACAL && ISA && ISA_DMA_API
    help
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called ni65.

source "drivers/net/tulip/Kconfig"

config AT1700
    tristate "AT1700/1720 support (EXPERIMENTAL)"
    depends on (ISA || MCA_LEGACY) && EXPERIMENTAL
    select CRC32
    ---help---
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called at1700.

config DEPCA
    tristate "DEPCA, DE10x, DE200, DE201, DE202, DE422 support"
    depends on ISA || EISA || MCA
    select CRC32
    ---help---
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto> as well as
      <file:drivers/net/depca.c>.

      To compile this driver as a module, choose M here. The module
      will be called depca.

config HP100
    tristate "HP 10/100VG PCLAN (ISA, EISA, PCI) support"
    depends on ISA || EISA || PCI
    help
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called hp100.

config NET_ISA
    bool "Other ISA cards"
    depends on ISA
    ---help---
      If your network (Ethernet) card hasn't been mentioned yet and its
      bus system (that's the way the cards talks to the other components
      of your computer) is ISA (as opposed to EISA, VLB or PCI), say Y.
      Make sure you know the name of your card. Read the Ethernet-HOWTO,
      available from <http://www.tldp.org/docs.html#howto>.

      If unsure, say Y.

      Note that the answer to this question doesn't directly affect the
      kernel: saying N will just cause the configurator to skip all
      the remaining ISA network card questions. If you say Y, you will be
      asked for your specific card in the following questions.

config E2100
    tristate "Cabletron E21xx support"
    depends on NET_ISA
    select CRC32
    help
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called e2100.

config EWRK3
    tristate "EtherWORKS 3 (DE203, DE204, DE205) support"
    depends on NET_ISA
    select CRC32
    ---help---
      This driver supports the DE203, DE204 and DE205 network (Ethernet)
      cards. If this is for you, say Y and read
      <file:Documentation/networking/ewrk3.txt> in the kernel source as
      well as the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called ewrk3.

config EEXPRESS
    tristate "EtherExpress 16 support"
    depends on NET_ISA
    ---help---
      If you have an EtherExpress16 network (Ethernet) card, say Y and
      read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.  Note that the Intel
      EtherExpress16 card used to be regarded as a very poor choice
      because the driver was very unreliable. We now have a new driver
      that should do better.

      To compile this driver as a module, choose M here. The module
      will be called eexpress.

config EEXPRESS_PRO
    tristate "EtherExpressPro support/EtherExpress 10 (i82595) support"
    depends on NET_ISA
    ---help---
      If you have a network (Ethernet) card of this type, say Y. This
      driver supports Intel i82595{FX,TX} based boards. Note however
      that the EtherExpress PRO/100 Ethernet card has its own separate
      driver.  Please read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called eepro.

config HPLAN_PLUS
    tristate "HP PCLAN+ (27247B and 27252A) support"
    depends on NET_ISA
    select CRC32
    help
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called hp-plus.

config HPLAN
    tristate "HP PCLAN (27245 and other 27xxx series) support"
    depends on NET_ISA
    select CRC32
    help
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called hp.

config LP486E
    tristate "LP486E on board Ethernet"
    depends on NET_ISA
    help
      Say Y here to support the 82596-based on-board Ethernet controller
      for the Panther motherboard, which is one of the two shipped in the
      Intel Professional Workstation.

config ETH16I
    tristate "ICL EtherTeam 16i/32 support"
    depends on NET_ISA
    help
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called eth16i.

config NE2000
    tristate "NE2000/NE1000 support"
    depends on NET_ISA || (Q40 && m) || M32R || MACH_TX49XX
    select CRC32
    ---help---
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.  Many Ethernet cards
      without a specific driver are compatible with NE2000.

      If you have a PCI NE2000 card however, say N here and Y to "PCI
      NE2000 and clone support" under "EISA, VLB, PCI and on board
      controllers" below. If you have a NE2000 card and are running on
      an MCA system (a bus system used on some IBM PS/2 computers and
      laptops), say N here and Y to "NE/2 (ne2000 MCA version) support",
      below.

      To compile this driver as a module, choose M here. The module
      will be called ne.

config ZNET
    tristate "Zenith Z-Note support (EXPERIMENTAL)"
    depends on NET_ISA && EXPERIMENTAL && ISA_DMA_API
    help
      The Zenith Z-Note notebook computer has a built-in network
      (Ethernet) card, and this is the Linux driver for it. Note that the
      IBM Thinkpad 300 is compatible with the Z-Note and is also supported
      by this driver. Read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

config SEEQ8005
    tristate "SEEQ8005 support (EXPERIMENTAL)"
    depends on NET_ISA && EXPERIMENTAL
    help
      This is a driver for the SEEQ 8005 network (Ethernet) card.  If this
      is for you, read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called seeq8005.

config NE2_MCA
    tristate "NE/2 (ne2000 MCA version) support"
    depends on MCA_LEGACY
    select CRC32
    help
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called ne2.

config IBMLANA
    tristate "IBM LAN Adapter/A support"
    depends on MCA
    ---help---
      This is a Micro Channel Ethernet adapter.  You need to set
      CONFIG_MCA to use this driver.  It is both available as an in-kernel
      driver and as a module.

      To compile this driver as a module, choose M here. The only
      currently supported card is the IBM LAN Adapter/A for Ethernet.  It
      will both support 16K and 32K memory windows, however a 32K window
      gives a better security against packet losses.  Usage of multiple
      boards with this driver should be possible, but has not been tested
      up to now due to lack of hardware.

config IBMVETH
    tristate "IBM LAN Virtual Ethernet support"
    depends on PPC_PSERIES
    ---help---
      This driver supports virtual ethernet adapters on newer IBM iSeries
      and pSeries systems.

      To compile this driver as a module, choose M here. The module will
      be called ibmveth.

source "drivers/net/ibm_newemac/Kconfig"

config NET_PCI
    bool "EISA, VLB, PCI and on board controllers"
    depends on ISA || EISA || PCI
    help
      This is another class of network cards which attach directly to the
      bus. If you have one of those, say Y and read the Ethernet-HOWTO,
      available from <http://www.tldp.org/docs.html#howto>.

      Note that the answer to this question doesn't directly affect the
      kernel: saying N will just cause the configurator to skip all
      the questions about this class of network cards. If you say Y, you
      will be asked for your specific card in the following questions. If
      you are unsure, say Y.

config PCNET32
    tristate "AMD PCnet32 PCI support"
    depends on NET_PCI && PCI
    select CRC32
    select MII
    help
      If you have a PCnet32 or PCnetPCI based network (Ethernet) card,
      answer Y here and read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called pcnet32.

config AMD8111_ETH
    tristate "AMD 8111 (new PCI lance) support"
    depends on NET_PCI && PCI
    select CRC32
    select MII
    help
      If you have an AMD 8111-based PCI lance ethernet card,
      answer Y here and read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called amd8111e.

config ADAPTEC_STARFIRE
    tristate "Adaptec Starfire/DuraLAN support"
    depends on NET_PCI && PCI
    select CRC32
    select MII
    help
      Say Y here if you have an Adaptec Starfire (or DuraLAN) PCI network
      adapter. The DuraLAN chip is used on the 64 bit PCI boards from
      Adaptec e.g. the ANA-6922A. The older 32 bit boards use the tulip
      driver.

      To compile this driver as a module, choose M here: the module
      will be called starfire.  This is recommended.

config AC3200
    tristate "Ansel Communications EISA 3200 support (EXPERIMENTAL)"
    depends on NET_PCI && (ISA || EISA) && EXPERIMENTAL
    select CRC32
    help
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called ac3200.

config APRICOT
    tristate "Apricot Xen-II on board Ethernet"
    depends on NET_PCI && ISA
    help
      If you have a network (Ethernet) controller of this type, say Y and
      read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called apricot.

config B44
    tristate "Broadcom 440x/47xx ethernet support"
    depends on SSB_POSSIBLE && HAS_DMA
    select SSB
    select MII
    help
      If you have a network (Ethernet) controller of this type, say Y
      or M and read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called b44.

# Auto-select SSB PCI-HOST support, if possible
config B44_PCI_AUTOSELECT
    bool
    depends on B44 && SSB_PCIHOST_POSSIBLE
    select SSB_PCIHOST
    default y

# Auto-select SSB PCICORE driver, if possible
config B44_PCICORE_AUTOSELECT
    bool
    depends on B44 && SSB_DRIVER_PCICORE_POSSIBLE
    select SSB_DRIVER_PCICORE
    default y

config B44_PCI
    bool
    depends on B44_PCI_AUTOSELECT && B44_PCICORE_AUTOSELECT
    default y

config FORCEDETH
    tristate "nForce Ethernet support"
    depends on NET_PCI && PCI
    help
      If you have a network (Ethernet) controller of this type, say Y and
      read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called forcedeth.

config FORCEDETH_NAPI
    bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
    depends on FORCEDETH && EXPERIMENTAL
    help
      NAPI is a new driver API designed to reduce CPU and interrupt load
      when the driver is receiving lots of packets from the card. It is
      still somewhat experimental and thus not yet enabled by default.

      If your estimated Rx load is 10kpps or more, or if the card will be
      deployed on potentially unfriendly networks (e.g. in a firewall),
      then say Y here.

      If in doubt, say N.

config CS89x0
    tristate "CS89x0 support"
    depends on NET_ETHERNET && (ISA || EISA || MACH_IXDP2351 \
        || ARCH_IXDP2X01 || ARCH_PNX010X || MACH_MX31ADS)
    ---help---
      Support for CS89x0 chipset based Ethernet cards. If you have a
      network (Ethernet) card of this type, say Y and read the
      Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto> as well as
      <file:Documentation/networking/cs89x0.txt>.

      To compile this driver as a module, choose M here. The module
      will be called cs89x0.

config CS89x0_NONISA_IRQ
    def_bool y
    depends on CS89x0 != n
    depends on MACH_IXDP2351 || ARCH_IXDP2X01 || ARCH_PNX010X || MACH_MX31ADS

config TC35815
    tristate "TOSHIBA TC35815 Ethernet support"
    depends on NET_PCI && PCI && MIPS
    select PHYLIB

config EEPRO100
    tristate "EtherExpressPro/100 support (eepro100, original Becker driver)"
    depends on NET_PCI && PCI
    select MII
    help
      If you have an Intel EtherExpress PRO/100 PCI network (Ethernet)
      card, say Y and read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called eepro100.


config E100
    tristate "Intel(R) PRO/100+ support"
    depends on NET_PCI && PCI
    select MII
    ---help---
      This driver supports Intel(R) PRO/100 family of adapters.
      To verify that your adapter is supported, find the board ID number
      on the adapter. Look for a label that has a barcode and a number
      in the format 123456-001 (six digits hyphen three digits).

      Use the above information and the Adapter & Driver ID Guide at:

      <http://support.intel.com/support/network/adapter/pro100/21397.htm>

          to identify the adapter.

      For the latest Intel PRO/100 network driver for Linux, see:

      <http://appsr.intel.com/scripts-df/support_intel.asp>

      More specific information on configuring the driver is in
      <file:Documentation/networking/e100.txt>.

      To compile this driver as a module, choose M here. The module
      will be called e100.

config LNE390
    tristate "Mylex EISA LNE390A/B support (EXPERIMENTAL)"
    depends on NET_PCI && EISA && EXPERIMENTAL
    select CRC32
    help
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called lne390.

config FEALNX
    tristate "Myson MTD-8xx PCI Ethernet support"
    depends on NET_PCI && PCI
    select CRC32
    select MII
    help
      Say Y here to support the Mysom MTD-800 family of PCI-based Ethernet
      cards. Specifications and data at
      <http://www.myson.com.hk/mtd/datasheet/>.

config NATSEMI
    tristate "National Semiconductor DP8381x series PCI Ethernet support"
    depends on NET_PCI && PCI
    select CRC32
    help
      This driver is for the National Semiconductor DP83810 series,
      which is used in cards from PureData, NetGear, Linksys
      and others, including the 83815 chip.
      More specific information and updates are available from
      <http://www.scyld.com/network/natsemi.html>.

config NE2K_PCI
    tristate "PCI NE2000 and clones support (see help)"
    depends on NET_PCI && PCI
    select CRC32
    ---help---
      This driver is for NE2000 compatible PCI cards. It will not work
      with ISA NE2000 cards (they have their own driver, "NE2000/NE1000
      support" below). If you have a PCI NE2000 network (Ethernet) card,
      say Y and read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      This driver also works for the following NE2000 clone cards:
      RealTek RTL-8029  Winbond 89C940  Compex RL2000  KTI ET32P2
      NetVin NV5000SC   Via 86C926      SureCom NE34   Winbond
      Holtek HT80232    Holtek HT80229

      To compile this driver as a module, choose M here. The module
      will be called ne2k-pci.

config NE3210
    tristate "Novell/Eagle/Microdyne NE3210 EISA support (EXPERIMENTAL)"
    depends on NET_PCI && EISA && EXPERIMENTAL
    select CRC32
    ---help---
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.  Note that this driver
      will NOT WORK for NE3200 cards as they are completely different.

      To compile this driver as a module, choose M here. The module
      will be called ne3210.

config ES3210
    tristate "Racal-Interlan EISA ES3210 support (EXPERIMENTAL)"
    depends on NET_PCI && EISA && EXPERIMENTAL
    select CRC32
    help
      If you have a network (Ethernet) card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module
      will be called es3210.

config 8139CP
    tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support (EXPERIMENTAL)"
    depends on NET_PCI && PCI && EXPERIMENTAL
    select CRC32
    select MII
    help
      This is a driver for the Fast Ethernet PCI network cards based on
      the RTL8139C+ chips. If you have one of those, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here: the module
      will be called 8139cp.  This is recommended.

config 8139TOO
    tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support"
    depends on NET_PCI && PCI
    select CRC32
    select MII
    ---help---
      This is a driver for the Fast Ethernet PCI network cards based on
      the RTL 8129/8130/8139 chips. If you have one of those, say Y and
      read the Ethernet-HOWTO <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here: the module
      will be called 8139too.  This is recommended.

config 8139TOO_PIO
    bool "Use PIO instead of MMIO"
    default y
    depends on 8139TOO
    help
      This instructs the driver to use programmed I/O ports (PIO) instead
      of PCI shared memory (MMIO).  This can possibly solve some problems
      in case your mainboard has memory consistency issues.  If unsure,
      say N.

config 8139TOO_TUNE_TWISTER
    bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)"
    depends on 8139TOO
    help
      This implements a function which might come in handy in case you
      are using low quality on long cabling. It is required for RealTek
      RTL-8139 revision K boards, and totally unused otherwise.  It tries
      to match the transceiver to the cable characteristics. This is
      experimental since hardly documented by the manufacturer.
      If unsure, say Y.

config 8139TOO_8129
    bool "Support for older RTL-8129/8130 boards"
    depends on 8139TOO
    help
      This enables support for the older and uncommon RTL-8129 and
      RTL-8130 chips, which support MII via an external transceiver,
      instead of an internal one.  Disabling this option will save some
      memory by making the code size smaller.  If unsure, say Y.

config 8139_OLD_RX_RESET
    bool "Use older RX-reset method"
    depends on 8139TOO
    help
      The 8139too driver was recently updated to contain a more rapid
      reset sequence, in the face of severe receive errors.  This "new"
      RX-reset method should be adequate for all boards.  But if you
      experience problems, you can enable this option to restore the
      old RX-reset behavior.  If unsure, say N.

config R6040
    tristate "RDC R6040 Fast Ethernet Adapter support (EXPERIMENTAL)"
    depends on NET_PCI && PCI
    select CRC32
    select MII
    help
      This is a driver for the R6040 Fast Ethernet MACs found in the
      the RDC R-321x System-on-chips.

      To compile this driver as a module, choose M here: the module
      will be called r6040. This is recommended.

config SIS900
    tristate "SiS 900/7016 PCI Fast Ethernet Adapter support"
    depends on NET_PCI && PCI
    select CRC32
    select MII
    ---help---
      This is a driver for the Fast Ethernet PCI network cards based on
      the SiS 900 and SiS 7016 chips. The SiS 900 core is also embedded in
      SiS 630 and SiS 540 chipsets.

      This driver also supports AMD 79C901 HomePNA so that you can use
      your phone line as a network cable.

      To compile this driver as a module, choose M here: the module
      will be called sis900.  This is recommended.

config EPIC100
    tristate "SMC EtherPower II"
    depends on NET_PCI && PCI
    select CRC32
    select MII
    help
      This driver is for the SMC EtherPower II 9432 PCI Ethernet NIC,
      which is based on the SMC83c17x (EPIC/100).
      More specific information and updates are available from
      <http://www.scyld.com/network/epic100.html>.

config SUNDANCE
    tristate "Sundance Alta support"
    depends on NET_PCI && PCI
    select CRC32
    select MII
    help
      This driver is for the Sundance "Alta" chip.
      More specific information and updates are available from
      <http://www.scyld.com/network/sundance.html>.

config SUNDANCE_MMIO
    bool "Use MMIO instead of PIO"
    depends on SUNDANCE
    help
      Enable memory-mapped I/O for interaction with Sundance NIC registers.
      Do NOT enable this by default, PIO (enabled when MMIO is disabled)
      is known to solve bugs on certain chips.

      If unsure, say N.

config TLAN
    tristate "TI ThunderLAN support"
    depends on NET_PCI && (PCI || EISA)
    ---help---
      If you have a PCI Ethernet network card based on the ThunderLAN chip
      which is supported by this driver, say Y and read the
      Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      Devices currently supported by this driver are Compaq Netelligent,
      Compaq NetFlex and Olicom cards.  Please read the file
      <file:Documentation/networking/tlan.txt> for more details.

      To compile this driver as a module, choose M here. The module
      will be called tlan.

      Please email feedback to <[e-mail]>.

config VIA_RHINE
    tristate "VIA Rhine support"
    depends on NET_PCI && PCI
    select CRC32
    select MII
    help
      If you have a VIA "Rhine" based network card (Rhine-I (VT86C100A),
      Rhine-II (VT6102), or Rhine-III (VT6105)), say Y here. Rhine-type
      Ethernet functions can also be found integrated on South Bridges
      (e.g. VT8235).

      To compile this driver as a module, choose M here. The module
      will be called via-rhine.

config VIA_RHINE_MMIO
    bool "Use MMIO instead of PIO"
    depends on VIA_RHINE
    help
      This instructs the driver to use PCI shared memory (MMIO) instead of
      programmed I/O ports (PIO). Enabling this gives an improvement in
      processing time in parts of the driver.

      If unsure, say Y.

config SC92031
    tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)"
    depends on NET_PCI && PCI && EXPERIMENTAL
    select CRC32
    ---help---
      This is a driver for the Fast Ethernet PCI network cards based on
      the Silan SC92031 chip (sometimes also called Rsltek 8139D). If you
      have one of these, say Y here.

      To compile this driver as a module, choose M here: the module
      will be called sc92031.  This is recommended.

config CPMAC
    tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
    depends on NET_ETHERNET && EXPERIMENTAL && AR7 && BROKEN
    select PHYLIB
    help
      TI AR7 CPMAC Ethernet support

config NET_POCKET
    bool "Pocket and portable adapters"
    depends on PARPORT
    ---help---
      Cute little network (Ethernet) devices which attach to the parallel
      port ("pocket adapters"), commonly used with laptops. If you have
      one of those, say Y and read the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      If you want to plug a network (or some other) card into the PCMCIA
      (or PC-card) slot of your laptop instead (PCMCIA is the standard for
      credit card size extension cards used by all modern laptops), you
      need the pcmcia-cs package (location contained in the file
      <file:Documentation/Changes>) and you can say N here.

      Laptop users should read the Linux Laptop home page at
      <http://www.linux-on-laptops.com/> or
      Tuxmobil - Linux on Mobile Computers at <http://www.tuxmobil.org/>.

      Note that the answer to this question doesn't directly affect the
      kernel: saying N will just cause the configurator to skip all
      the questions about this class of network devices. If you say Y, you
      will be asked for your specific device in the following questions.

config ATP
    tristate "AT-LAN-TEC/RealTek pocket adapter support"
    depends on NET_POCKET && PARPORT && X86
    select CRC32
    ---help---
      This is a network (Ethernet) device which attaches to your parallel
      port. Read <file:drivers/net/atp.c> as well as the Ethernet-HOWTO,
      available from <http://www.tldp.org/docs.html#howto>, if you
      want to use this.  If you intend to use this driver, you should have
      said N to the "Parallel printer support", because the two drivers
      don't like each other.

      To compile this driver as a module, choose M here: the module
      will be called atp.

config DE600
    tristate "D-Link DE600 pocket adapter support"
    depends on NET_POCKET && PARPORT
    ---help---
      This is a network (Ethernet) device which attaches to your parallel
      port. Read <file:Documentation/networking/DLINK.txt> as well as the
      Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>, if you want to use
      this. It is possible to have several devices share a single parallel
      port and it is safe to compile the corresponding drivers into the
      kernel.

      To compile this driver as a module, choose M here: the module
      will be called de600.

config DE620
    tristate "D-Link DE620 pocket adapter support"
    depends on NET_POCKET && PARPORT
    ---help---
      This is a network (Ethernet) device which attaches to your parallel
      port. Read <file:Documentation/networking/DLINK.txt> as well as the
      Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>, if you want to use
      this. It is possible to have several devices share a single parallel
      port and it is safe to compile the corresponding drivers into the
      kernel.

      To compile this driver as a module, choose M here: the module
      will be called de620.

config SGISEEQ
    tristate "SGI Seeq ethernet controller support"
    depends on SGI_HAS_SEEQ
    help
      Say Y here if you have an Seeq based Ethernet network card. This is
      used in many Silicon Graphics machines.

config DECLANCE
    tristate "DEC LANCE ethernet controller support"
    depends on MACH_DECSTATION
    select CRC32
    help
      This driver is for the series of Ethernet controllers produced by
      DEC (now Compaq) based on the AMD Lance chipset, including the
      DEPCA series.  (This chipset is better known via the NE2100 cards.)

config 68360_ENET
    bool "Motorola 68360 ethernet controller"
    depends on M68360
    help
      Say Y here if you want to use the built-in ethernet controller of
      the Motorola 68360 processor.

config FEC
    bool "FEC ethernet controller (of ColdFire CPUs)"
    depends on M523x || M527x || M5272 || M528x || M520x || ARCH_MX51
    help
      Say Y here if you want to use the built-in 10/100 Fast ethernet
      controller on some Motorola ColdFire/Freescale processors.

config FEC2
    bool "Second FEC ethernet controller (on some ColdFire CPUs)"
    depends on FEC
    help
      Say Y here if you want to use the second built-in 10/100 Fast
      ethernet controller on some Motorola ColdFire processors.

config FEC_MPC52xx
    tristate "MPC52xx FEC driver"
    depends on PPC_MPC52xx && PPC_BESTCOMM
    select CRC32
    select PHYLIB
    select PPC_BESTCOMM_FEC
    ---help---
      This option enables support for the MPC5200's on-chip
      Fast Ethernet Controller
      If compiled as module, it will be called 'fec_mpc52xx.ko'.

config FEC_MPC52xx_MDIO
    bool "MPC52xx FEC MDIO bus driver"
    depends on FEC_MPC52xx
    default y
    ---help---
      The MPC5200's FEC can connect to the Ethernet either with
      an external MII PHY chip or 10 Mbps 7-wire interface
      (Motorola? industry standard).
      If your board uses an external PHY connected to FEC, enable this.
      If not sure, enable.
      If compiled as module, it will be called 'fec_mpc52xx_phy.ko'.

config NE_H8300
    tristate "NE2000 compatible support for H8/300"
    depends on H8300
    help
      Say Y here if you want to use the NE2000 compatible
      controller on the Renesas H8/300 processor.

config ATL2
    tristate "Atheros L2 Fast Ethernet support"
    depends on PCI
    select CRC32
    select MII
    help
      This driver supports the Atheros L2 fast ethernet adapter.

      To compile this driver as a module, choose M here.  The module
      will be called atl2.

source "drivers/net/fs_enet/Kconfig"

endif # NET_ETHERNET

#
#    Gigabit Ethernet
#

menuconfig NETDEV_1000
    bool "Ethernet (1000 Mbit)"
    depends on !UML
    default y
    ---help---
      Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
      type of Local Area Network (LAN) in universities and companies.

      Say Y here to get to see options for Gigabit Ethernet drivers.
      This option alone does not add any kernel code.
      Note that drivers supporting both 100 and 1000 MBit may be listed
      under "Ethernet (10 or 100MBit)" instead.

      If you say N, all options in this submenu will be skipped and disabled.

if NETDEV_1000

config ACENIC
    tristate "Alteon AceNIC/3Com 3C985/NetGear GA620 Gigabit support"
    depends on PCI
    ---help---
      Say Y here if you have an Alteon AceNIC, 3Com 3C985(B), NetGear
      GA620, SGI Gigabit or Farallon PN9000-SX PCI Gigabit Ethernet
      adapter. The driver allows for using the Jumbo Frame option (9000
      bytes/frame) however it requires that your switches can handle this
      as well. To enable Jumbo Frames, add `mtu 9000' to your ifconfig
      line.

      To compile this driver as a module, choose M here: the
      module will be called acenic.

config ACENIC_OMIT_TIGON_I
    bool "Omit support for old Tigon I based AceNICs"
    depends on ACENIC
    help
      Say Y here if you only have Tigon II based AceNICs and want to leave
      out support for the older Tigon I based cards which are no longer
      being sold (ie. the original Alteon AceNIC and 3Com 3C985 (non B
      version)).  This will reduce the size of the driver object by
      app. 100KB.  If you are not sure whether your card is a Tigon I or a
      Tigon II, say N here.

      The safe and default value for this is N.

config DL2K
    tristate "DL2000/TC902x-based Gigabit Ethernet support"
    depends on PCI
    select CRC32
    help
      This driver supports DL2000/TC902x-based Gigabit ethernet cards,
      which includes
      D-Link DGE-550T Gigabit Ethernet Adapter.
      D-Link DL2000-based Gigabit Ethernet Adapter.
      Sundance/Tamarack TC902x Gigabit Ethernet Adapter.

      To compile this driver as a module, choose M here: the
      module will be called dl2k.

config E1000
    tristate "Intel(R) PRO/1000 Gigabit Ethernet support"
    depends on PCI
    ---help---
      This driver supports Intel(R) PRO/1000 gigabit ethernet family of
      adapters.  For more information on how to identify your adapter, go
      to the Adapter & Driver ID Guide at:

      <http://support.intel.com/support/network/adapter/pro100/21397.htm>

      For general information and support, go to the Intel support
      website at:

      <http://support.intel.com>

      More specific information on configuring the driver is in
      <file:Documentation/networking/e1000.txt>.

      To compile this driver as a module, choose M here. The module
      will be called e1000.

config E1000E
    tristate "Intel(R) PRO/1000 PCI-Express Gigabit Ethernet support"
    depends on PCI && (!SPARC32 || BROKEN)
    ---help---
      This driver supports the PCI-Express Intel(R) PRO/1000 gigabit
      ethernet family of adapters. For PCI or PCI-X e1000 adapters,
      use the regular e1000 driver For more information on how to
      identify your adapter, go to the Adapter & Driver ID Guide at:

      <http://support.intel.com/support/network/adapter/pro100/21397.htm>

      For general information and support, go to the Intel support
      website at:

      <http://support.intel.com>

      To compile this driver as a module, choose M here. The module
      will be called e1000e.

config IP1000
    tristate "IP1000 Gigabit Ethernet support"
    depends on PCI && EXPERIMENTAL
    select MII
    ---help---
      This driver supports IP1000 gigabit Ethernet cards.

      To compile this driver as a module, choose M here: the module
      will be called ipg.  This is recommended.

config IGB
       tristate "Intel(R) 82575 PCI-Express Gigabit Ethernet support"
       depends on PCI
       ---help---
         This driver supports Intel(R) 82575 gigabit ethernet family of
         adapters.  For more information on how to identify your adapter, go
         to the Adapter & Driver ID Guide at:

         <http://support.intel.com/support/network/adapter/pro100/21397.htm>

         For general information and support, go to the Intel support
         website at:

         <http://support.intel.com>

         More specific information on configuring the driver is in
         <file:Documentation/networking/e1000.txt>.

         To compile this driver as a module, choose M here. The module
         will be called igb.

config IGB_LRO
    bool "Use software LRO"
    depends on IGB && INET
    select INET_LRO
    ---help---
      Say Y here if you want to use large receive offload.

      If in doubt, say N.

config IGB_DCA
    bool "Direct Cache Access (DCA) Support"
    default y
    depends on IGB && DCA && !(IGB=y && DCA=m)
    ---help---
      Say Y here if you want to use Direct Cache Access (DCA) in the
      driver.  DCA is a method for warming the CPU cache before data
      is used, with the intent of lessening the impact of cache misses.

source "drivers/net/ixp2000/Kconfig"

config MYRI_SBUS
    tristate "MyriCOM Gigabit Ethernet support"
    depends on SBUS
    help
      This driver supports MyriCOM Sbus gigabit Ethernet cards.

      To compile this driver as a module, choose M here: the module
      will be called myri_sbus.  This is recommended.

config NS83820
    tristate "National Semiconductor DP83820 support"
    depends on PCI
    help
      This is a driver for the National Semiconductor DP83820 series
      of gigabit ethernet MACs.  Cards using this chipset include
      the D-Link DGE-500T, PureData's PDP8023Z-TG, SMC's SMC9462TX,
      SOHO-GA2000T, SOHO-GA2500T.  The driver supports the use of
      zero copy.

config HAMACHI
    tristate "Packet Engines Hamachi GNIC-II support"
    depends on PCI
    select MII
    help
      If you have a Gigabit Ethernet card of this type, say Y and read
      the Ethernet-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>.

      To compile this driver as a module, choose M here. The module will be
      called hamachi.

config YELLOWFIN
    tristate "Packet Engines Yellowfin Gigabit-NIC support (EXPERIMENTAL)"
    depends on PCI && EXPERIMENTAL
    select CRC32
    ---help---
      Say Y here if you have a Packet Engines G-NIC PCI Gigabit Ethernet
      adapter or the SYM53C885 Ethernet controller. The Gigabit adapter is
      used by the Beowulf Linux cluster project.  See
      <http://cesdis.gsfc.nasa.gov/linux/drivers/yellowfin.html> for more
      information about this driver in particular and Beowulf in general.

      To compile this driver as a module, choose M here: the module
      will be called yellowfin.  This is recommended.

config R8169
    tristate "Realtek 8169 gigabit ethernet support"
    depends on PCI
    select CRC32
    select MII
    ---help---
      Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter.

      To compile this driver as a module, choose M here: the module
      will be called r8169.  This is recommended.

config R8169_VLAN
    bool "VLAN support"
    depends on R8169 && VLAN_8021Q
    ---help---
      Say Y here for the r8169 driver to support the functions required
      by the kernel 802.1Q code.

      If in doubt, say Y.

config SB1250_MAC
    tristate "SB1250 Gigabit Ethernet support"
    depends on SIBYTE_SB1xxx_SOC
    select PHYLIB
    ---help---
      This driver supports Gigabit Ethernet interfaces based on the
      Broadcom SiByte family of System-On-a-Chip parts.  They include
      the BCM1120, BCM1125, BCM1125H, BCM1250, BCM1255, BCM1280, BCM1455
      and BCM1480 chips.

      To compile this driver as a module, choose M here: the module
      will be called sb1250-mac.

config SIS190
    tristate "SiS190/SiS191 gigabit ethernet support"
    depends on PCI
    select CRC32
    select MII
    ---help---
      Say Y here if you have a SiS 190 PCI Fast Ethernet adapter or
      a SiS 191 PCI Gigabit Ethernet adapter. Both are expected to
      appear in lan on motherboard designs which are based on SiS 965
      and SiS 966 south bridge.

      To compile this driver as a module, choose M here: the module
      will be called sis190.  This is recommended.

config SKGE
    tristate "New SysKonnect GigaEthernet support"
    depends on PCI
    select CRC32
    ---help---
      This driver support the Marvell Yukon or SysKonnect SK-98xx/SK-95xx
      and related Gigabit Ethernet adapters. It is a new smaller driver
      with better performance and more complete ethtool support.

      It does not support the link failover and network management
      features that "portable" vendor supplied sk98lin driver does.

      This driver supports adapters based on the original Yukon chipset:
      Marvell 88E8001, Belkin F5D5005, CNet GigaCard, DLink DGE-530T,
      Linksys EG1032/EG1064, 3Com 3C940/3C940B, SysKonnect SK-9871/9872.

      It does not support the newer Yukon2 chipset: a separate driver,
      sky2, is provided for Yukon2-based adapters.

      To compile this driver as a module, choose M here: the module
      will be called skge.  This is recommended.

config SKGE_DEBUG
       bool "Debugging interface"
       depends on SKGE && DEBUG_FS
       help
     This option adds the ability to dump driver state for debugging.
     The file debugfs/skge/ethX displays the state of the internal
     transmit and receive rings.

     If unsure, say N.

config SKY2
    tristate "SysKonnect Yukon2 support"
    depends on PCI
    select CRC32
    ---help---
      This driver supports Gigabit Ethernet adapters based on the
      Marvell Yukon 2 chipset:
      Marvell 88E8021/88E8022/88E8035/88E8036/88E8038/88E8050/88E8052/
      88E8053/88E8055/88E8061/88E8062, SysKonnect SK-9E21D/SK-9S21

      There is companion driver for the older Marvell Yukon and
      Genesis based adapters: skge.

      To compile this driver as a module, choose M here: the module
      will be called sky2.  This is recommended.

config SKY2_DEBUG
       bool "Debugging interface"
       depends on SKY2 && DEBUG_FS
       help
     This option adds the ability to dump driver state for debugging.
     The file debugfs/sky2/ethX displays the state of the internal
     transmit and receive rings.

     If unsure, say N.

config VIA_VELOCITY
    tristate "VIA Velocity support"
    depends on PCI
    select CRC32
    select CRC_CCITT
    select MII
    help
      If you have a VIA "Velocity" based network card say Y here.

      To compile this driver as a module, choose M here. The module
      will be called via-velocity.

config TIGON3
    tristate "Broadcom Tigon3 support"
    depends on PCI
    select PHYLIB
    help
      This driver supports Broadcom Tigon3 based gigabit Ethernet cards.

      To compile this driver as a module, choose M here: the module
      will be called tg3.  This is recommended.

config BNX2
    tristate "Broadcom NetXtremeII support"
    depends on PCI
    select CRC32
    select ZLIB_INFLATE
    help
      This driver supports Broadcom NetXtremeII gigabit Ethernet cards.

      To compile this driver as a module, choose M here: the module
      will be called bnx2.  This is recommended.

config SPIDER_NET
    tristate "Spider Gigabit Ethernet driver"
    depends on PCI && (PPC_IBM_CELL_BLADE || PPC_CELLEB)
    select FW_LOADER
    help
      This driver supports the Gigabit Ethernet chips present on the
      Cell Processor-Based Blades from IBM.

config TSI108_ETH
       tristate "Tundra TSI108 gigabit Ethernet support"
       depends on TSI108_BRIDGE
       help
         This driver supports Tundra TSI108 gigabit Ethernet ports.
         To compile this driver as a module, choose M here: the module
         will be called tsi108_eth.

config GELIC_NET
    tristate "PS3 Gigabit Ethernet driver"
    depends on PPC_PS3
    select PS3_SYS_MANAGER
    help
      This driver supports the network device on the PS3 game
      console.  This driver has built-in support for Ethernet.

      To compile this driver as a module, choose M here: the
      module will be called ps3_gelic.

config GELIC_WIRELESS
    bool "PS3 Wireless support"
    depends on GELIC_NET
    select WIRELESS_EXT
    help
      This option adds the support for the wireless feature of PS3.
      If you have the wireless-less model of PS3 or have no plan to
      use wireless feature, disabling this option saves memory.  As
      the driver automatically distinguishes the models, you can
      safely enable this option even if you have a wireless-less model.

config GELIC_WIRELESS_OLD_PSK_INTERFACE
       bool "PS3 Wireless private PSK interface (OBSOLETE)"
       depends on GELIC_WIRELESS
       help
          This option retains the obsolete private interface to pass
          the PSK from user space programs to the driver.  The PSK
          stands for 'Pre Shared Key' and is used for WPA[2]-PSK
          (WPA-Personal) environment.
          If WPA[2]-PSK is used and you need to use old programs that
          support only this old interface, say Y.  Otherwise N.

          If unsure, say N.

config GIANFAR
    tristate "Gianfar Ethernet"
    depends on FSL_SOC
    select PHYLIB
    select CRC32
    help
      This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
      and MPC86xx family of chips, and the FEC on the 8540.

config UCC_GETH
    tristate "Freescale QE Gigabit Ethernet"
    depends on QUICC_ENGINE
    select PHYLIB
    help
      This driver supports the Gigabit Ethernet mode of the QUICC Engine,
      which is available on some Freescale SOCs.

config UGETH_MAGIC_PACKET
    bool "Magic Packet detection support"
    depends on UCC_GETH

config UGETH_FILTERING
    bool "Mac address filtering support"
    depends on UCC_GETH

config UGETH_TX_ON_DEMAND
    bool "Transmit on Demand support"
    depends on UCC_GETH

config MV643XX_ETH
    tristate "Marvell Discovery (643XX) and Orion ethernet support"
    depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32) || PLAT_ORION
    select PHYLIB
    help
      This driver supports the gigabit ethernet MACs in the
      Marvell Discovery PPC/MIPS chipset family (MV643XX) and
      in the Marvell Orion ARM SoC family.

      Some boards that use the Discovery chipset are the Momenco
      Ocelot C and Jaguar ATX and Pegasos II.

config QLA3XXX
    tristate "QLogic QLA3XXX Network Driver Support"
    depends on PCI
    help
      This driver supports QLogic ISP3XXX gigabit Ethernet cards.

      To compile this driver as a module, choose M here: the module
      will be called qla3xxx.

config ATL1
    tristate "Atheros/Attansic L1 Gigabit Ethernet support"
    depends on PCI
    select CRC32
    select MII
    help
      This driver supports the Atheros/Attansic L1 gigabit ethernet
      adapter.

      To compile this driver as a module, choose M here.  The module
      will be called atl1.

config ATL1E
    tristate "Atheros L1E Gigabit Ethernet support (EXPERIMENTAL)"
    depends on PCI && EXPERIMENTAL
    select CRC32
    select MII
    help
      This driver supports the Atheros L1E gigabit ethernet adapter.

      To compile this driver as a module, choose M here.  The module
      will be called atl1e.

config JME
    tristate "JMicron(R) PCI-Express Gigabit Ethernet support"
    depends on PCI
    select CRC32
    select MII
    ---help---
      This driver supports the PCI-Express gigabit ethernet adapters
      based on JMicron JMC250 chipset.

      To compile this driver as a module, choose M here. The module
      will be called jme.

endif # NETDEV_1000

#
#    10 Gigabit Ethernet
#

menuconfig NETDEV_10000
    bool "Ethernet (10000 Mbit)"
    depends on !UML
    default y
    ---help---
      Say Y here to get to see options for 10 Gigabit Ethernet drivers.
      This option alone does not add any kernel code.

      If you say N, all options in this submenu will be skipped and disabled.

if NETDEV_10000

config CHELSIO_T1
        tristate "Chelsio 10Gb Ethernet support"
        depends on PCI
    select CRC32
        help
          This driver supports Chelsio gigabit and 10-gigabit
          Ethernet cards. More information about adapter features and
      performance tuning is in <file:Documentation/networking/cxgb.txt>.

          For general information about Chelsio and our products, visit
          our website at <http://www.chelsio.com>.

          For customer support, please visit our customer support page at
          <http://www.chelsio.com/support.htm>.

          Please send feedback to <[e-mail]>.

          To compile this driver as a module, choose M here: the module
          will be called cxgb.

config CHELSIO_T1_1G
        bool "Chelsio gigabit Ethernet support"
        depends on CHELSIO_T1
        help
          Enables support for Chelsio's gigabit Ethernet PCI cards.  If you
          are using only 10G cards say 'N' here.

config CHELSIO_T3
    tristate "Chelsio Communications T3 10Gb Ethernet support"
    depends on PCI && INET
    select FW_LOADER
    select INET_LRO
    help
      This driver supports Chelsio T3-based gigabit and 10Gb Ethernet
      adapters.

      For general information about Chelsio and our products, visit
      our website at <http://www.chelsio.com>.

      For customer support, please visit our customer support page at
      <http://www.chelsio.com/support.htm>.

      Please send feedback to <[e-mail]>.

      To compile this driver as a module, choose M here: the module
      will be called cxgb3.

config EHEA
    tristate "eHEA Ethernet support"
    depends on IBMEBUS && INET && SPARSEMEM
    select INET_LRO
    ---help---
      This driver supports the IBM pSeries eHEA ethernet adapter.

      To compile the driver as a module, choose M here. The module
      will be called ehea.

config ENIC
    tristate "Cisco 10G Ethernet NIC support"
    depends on PCI && INET
    select INET_LRO
    help
      This enables the support for the Cisco 10G Ethernet card.

config IXGBE
    tristate "Intel(R) 10GbE PCI Express adapters support"
    depends on PCI && INET
    select INET_LRO
    ---help---
      This driver supports Intel(R) 10GbE PCI Express family of
      adapters.  For more information on how to identify your adapter, go
      to the Adapter & Driver ID Guide at:

      <http://support.intel.com/support/network/adapter/pro100/21397.htm>

      For general information and support, go to the Intel support
      website at:

      <http://support.intel.com>

      To compile this driver as a module, choose M here. The module
      will be called ixgbe.

config IXGBE_DCA
    bool "Direct Cache Access (DCA) Support"
    default y
    depends on IXGBE && DCA && !(IXGBE=y && DCA=m)
    ---help---
      Say Y here if you want to use Direct Cache Access (DCA) in the
      driver.  DCA is a method for warming the CPU cache before data
      is used, with the intent of lessening the impact of cache misses.

config IXGB
    tristate "Intel(R) PRO/10GbE support"
    depends on PCI
    ---help---
      This driver supports Intel(R) PRO/10GbE family of adapters for
      PCI-X type cards. For PCI-E type cards, use the "ixgbe" driver
      instead. For more information on how to identify your adapter, go
      to the Adapter & Driver ID Guide at:

      <http://support.intel.com/support/network/adapter/pro100/21397.htm>

      For general information and support, go to the Intel support
      website at:

      <http://support.intel.com>

      More specific information on configuring the driver is in
      <file:Documentation/networking/ixgb.txt>.

      To compile this driver as a module, choose M here. The module
      will be called ixgb.

config S2IO
    tristate "S2IO 10Gbe XFrame NIC"
    depends on PCI
    ---help---
      This driver supports the 10Gbe XFrame NIC of S2IO.
      More specific information on configuring the driver is in
      <file:Documentation/networking/s2io.txt>.

config MYRI10GE
    tristate "Myricom Myri-10G Ethernet support"
    depends on PCI && INET
    select FW_LOADER
    select CRC32
    select INET_LRO
    ---help---
      This driver supports Myricom Myri-10G Dual Protocol interface in
      Ethernet mode. If the eeprom on your board is not recent enough,
      you will need a newer firmware image.
      You may get this image or more information, at:

      <http://www.myri.com/scs/download-Myri10GE.html>

      To compile this driver as a module, choose M here. The module
      will be called myri10ge.

config MYRI10GE_DCA
    bool "Direct Cache Access (DCA) Support"
    default y
    depends on MYRI10GE && DCA && !(MYRI10GE=y && DCA=m)
    ---help---
      Say Y here if you want to use Direct Cache Access (DCA) in the
      driver.  DCA is a method for warming the CPU cache before data
      is used, with the intent of lessening the impact of cache misses.

config NETXEN_NIC
    tristate "NetXen Multi port (1/10) Gigabit Ethernet NIC"
    depends on PCI
    help
      This enables the support for NetXen's Gigabit Ethernet card.

config NIU
    tristate "Sun Neptune 10Gbit Ethernet support"
    depends on PCI
    help
      This enables support for cards based upon Sun's
      Neptune chipset.

config PASEMI_MAC
    tristate "PA Semi 1/10Gbit MAC"
    depends on PPC_PASEMI && PCI
    select PHYLIB
    select INET_LRO
    help
      This driver supports the on-chip 1/10Gbit Ethernet controller on
      PA Semi's PWRficient line of chips.

config MLX4_EN
    tristate "Mellanox Technologies 10Gbit Ethernet support"
    depends on PCI && INET
    select MLX4_CORE
    select INET_LRO
    help
      This driver supports Mellanox Technologies ConnectX Ethernet
      devices.

config MLX4_CORE
    tristate
    depends on PCI
    default n

config MLX4_DEBUG
    bool "Verbose debugging output" if (MLX4_CORE && EMBEDDED)
    depends on MLX4_CORE
    default y
    ---help---
      This option causes debugging code to be compiled into the
      mlx4_core driver.  The output can be turned on via the
      debug_level module parameter (which can also be set after
      the driver is loaded through sysfs).

config TEHUTI
    tristate "Tehuti Networks 10G Ethernet"
    depends on PCI
    help
      Tehuti Networks 10G Ethernet NIC

config BNX2X
    tristate "Broadcom NetXtremeII 10Gb support"
    depends on PCI
    select ZLIB_INFLATE
    select LIBCRC32C
    help
      This driver supports Broadcom NetXtremeII 10 gigabit Ethernet cards.
      To compile this driver as a module, choose M here: the module
      will be called bnx2x.  This is recommended.

config QLGE
    tristate "QLogic QLGE 10Gb Ethernet Driver Support"
    depends on PCI
    help
      This driver supports QLogic ISP8XXX 10Gb Ethernet cards.

      To compile this driver as a module, choose M here: the module
      will be called qlge.

source "drivers/net/sfc/Kconfig"

endif # NETDEV_10000

source "drivers/net/tokenring/Kconfig"

source "drivers/net/wireless/Kconfig"

source "drivers/net/usb/Kconfig"

source "drivers/net/pcmcia/Kconfig"

source "drivers/net/wan/Kconfig"

source "drivers/atm/Kconfig"

source "drivers/s390/net/Kconfig"

config XEN_NETDEV_FRONTEND
    tristate "Xen network device frontend driver"
    depends on XEN
    default y
    help
      The network device frontend driver allows the kernel to
      access network devices exported exported by a virtual
      machine containing a physical network device driver. The
      frontend driver is intended for unprivileged guest domains;
      if you are compiling a kernel for a Xen guest, you almost
      certainly want to enable this.

config ISERIES_VETH
    tristate "iSeries Virtual Ethernet driver support"
    depends on PPC_ISERIES

config RIONET
    tristate "RapidIO Ethernet over messaging driver support"
    depends on RAPIDIO

config RIONET_TX_SIZE
    int "Number of outbound queue entries"
    depends on RIONET
    default "128"

config RIONET_RX_SIZE
    int "Number of inbound queue entries"
    depends on RIONET
    default "128"

config FDDI
    bool "FDDI driver support"
    depends on (PCI || EISA || TC)
    help
      Fiber Distributed Data Interface is a high speed local area network
      design; essentially a replacement for high speed Ethernet. FDDI can
      run over copper or fiber. If you are connected to such a network and
      want a driver for the FDDI card in your computer, say Y here (and
      then also Y to the driver for your FDDI card, below). Most people
      will say N.

config DEFXX
    tristate "Digital DEFTA/DEFEA/DEFPA adapter support"
    depends on FDDI && (PCI || EISA || TC)
    ---help---
      This is support for the DIGITAL series of TURBOchannel (DEFTA),
      EISA (DEFEA) and PCI (DEFPA) controllers which can connect you
      to a local FDDI network.

      To compile this driver as a module, choose M here: the module
      will be called defxx.  If unsure, say N.

config DEFXX_MMIO
    bool
    prompt "Use MMIO instead of PIO" if PCI || EISA
    depends on DEFXX
    default n if PCI || EISA
    default y
    ---help---
      This instructs the driver to use EISA or PCI memory-mapped I/O
      (MMIO) as appropriate instead of programmed I/O ports (PIO).
      Enabling this gives an improvement in processing time in parts
      of the driver, but it may cause problems with EISA (DEFEA)
      adapters.  TURBOchannel does not have the concept of I/O ports,
      so MMIO is always used for these (DEFTA) adapters.

      If unsure, say N.

config SKFP
    tristate "SysKonnect FDDI PCI support"
    depends on FDDI && PCI
    select BITREVERSE
    ---help---
      Say Y here if you have a SysKonnect FDDI PCI adapter.
      The following adapters are supported by this driver:
      - SK-5521 (SK-NET FDDI-UP)
      - SK-5522 (SK-NET FDDI-UP DAS)
      - SK-5541 (SK-NET FDDI-FP)
      - SK-5543 (SK-NET FDDI-LP)
      - SK-5544 (SK-NET FDDI-LP DAS)
      - SK-5821 (SK-NET FDDI-UP64)
      - SK-5822 (SK-NET FDDI-UP64 DAS)
      - SK-5841 (SK-NET FDDI-FP64)
      - SK-5843 (SK-NET FDDI-LP64)
      - SK-5844 (SK-NET FDDI-LP64 DAS)
      - Netelligent 100 FDDI DAS Fibre SC
      - Netelligent 100 FDDI SAS Fibre SC
      - Netelligent 100 FDDI DAS UTP
      - Netelligent 100 FDDI SAS UTP
      - Netelligent 100 FDDI SAS Fibre MIC

      Read <file:Documentation/networking/skfp.txt> for information about
      the driver.

      Questions concerning this driver can be addressed to:
      <[e-mail]>

      To compile this driver as a module, choose M here: the module
      will be called skfp.  This is recommended.

config HIPPI
    bool "HIPPI driver support (EXPERIMENTAL)"
    depends on EXPERIMENTAL && INET && PCI
    help
      HIgh Performance Parallel Interface (HIPPI) is a 800Mbit/sec and
      1600Mbit/sec dual-simplex switched or point-to-point network. HIPPI
      can run over copper (25m) or fiber (300m on multi-mode or 10km on
      single-mode). HIPPI networks are commonly used for clusters and to
      connect to super computers. If you are connected to a HIPPI network
      and have a HIPPI network card in your computer that you want to use
      under Linux, say Y here (you must also remember to enable the driver
      for your HIPPI card below). Most people will say N here.

config ROADRUNNER
    tristate "Essential RoadRunner HIPPI PCI adapter support (EXPERIMENTAL)"
    depends on HIPPI && PCI
    help
      Say Y here if this is your PCI HIPPI network card.

      To compile this driver as a module, choose M here: the module
      will be called rrunner.  If unsure, say N.

config ROADRUNNER_LARGE_RINGS
    bool "Use large TX/RX rings (EXPERIMENTAL)"
    depends on ROADRUNNER
    help
      If you say Y here, the RoadRunner driver will preallocate up to 2 MB
      of additional memory to allow for fastest operation, both for
      transmitting and receiving. This memory cannot be used by any other
      kernel code or by user space programs. Say Y here only if you have
      the memory.

config PLIP
    tristate "PLIP (parallel port) support"
    depends on PARPORT
    ---help---
      PLIP (Parallel Line Internet Protocol) is used to create a
      reasonably fast mini network consisting of two (or, rarely, more)
      local machines.  A PLIP link from a Linux box is a popular means to
      install a Linux distribution on a machine which doesn't have a
      CD-ROM drive (a minimal system has to be transferred with floppies
      first). The kernels on both machines need to have this PLIP option
      enabled for this to work.

      The PLIP driver has two modes, mode 0 and mode 1.  The parallel
      ports (the connectors at the computers with 25 holes) are connected
      with "null printer" or "Turbo Laplink" cables which can transmit 4
      bits at a time (mode 0) or with special PLIP cables, to be used on
      bidirectional parallel ports only, which can transmit 8 bits at a
      time (mode 1); you can find the wiring of these cables in
      <file:Documentation/networking/PLIP.txt>.  The cables can be up to
      15m long.  Mode 0 works also if one of the machines runs DOS/Windows
      and has some PLIP software installed, e.g. the Crynwr PLIP packet
      driver (<http://oak.oakland.edu/simtel.net/msdos/pktdrvr-pre.html>)
      and winsock or NCSA's telnet.

      If you want to use PLIP, say Y and read the PLIP mini-HOWTO as well
      as the NET-3-HOWTO, both available from
      <http://www.tldp.org/docs.html#howto>.  Note that the PLIP
      protocol has been changed and this PLIP driver won't work together
      with the PLIP support in Linux versions 1.0.x.  This option enlarges
      your kernel by about 8 KB.

      To compile this driver as a module, choose M here. The module
      will be called plip. If unsure, say Y or M, in case you buy
      a laptop later.

config PPP
    tristate "PPP (point-to-point protocol) support"
    select SLHC
    ---help---
      PPP (Point to Point Protocol) is a newer and better SLIP.  It serves
      the same purpose: sending Internet traffic over telephone (and other
      serial) lines.  Ask your access provider if they support it, because
      otherwise you can't use it; most Internet access providers these
      days support PPP rather than SLIP.

      To use PPP, you need an additional program called pppd as described
      in the PPP-HOWTO, available at
      <http://www.tldp.org/docs.html#howto>.  Make sure that you have
      the version of pppd recommended in <file:Documentation/Changes>.
      The PPP option enlarges your kernel by about 16 KB.

      There are actually two versions of PPP: the traditional PPP for
      asynchronous lines, such as regular analog phone lines, and
      synchronous PPP which can be used over digital ISDN lines for
      example.  If you want to use PPP over phone lines or other
      asynchronous serial lines, you need to say Y (or M) here and also to
      the next option, "PPP support for async serial ports".  For PPP over
      synchronous lines, you should say Y (or M) here and to "Support
      synchronous PPP", below.

      If you said Y to "Version information on all symbols" above, then
      you cannot compile the PPP driver into the kernel; you can then only
      compile it as a module. To compile this driver as a module, choose M
      here. The module will be called ppp_generic.

config PPP_MULTILINK
    bool "PPP multilink support (EXPERIMENTAL)"
    depends on PPP && EXPERIMENTAL
    help
      PPP multilink is a protocol (defined in RFC 1990) which allows you
      to combine several (logical or physical) lines into one logical PPP
      connection, so that you can utilize your full bandwidth.

      This has to be supported at the other end as well and you need a
      version of the pppd daemon which understands the multilink protocol.

      If unsure, say N.

config PPP_FILTER
    bool "PPP filtering"
    depends on PPP
    help
      Say Y here if you want to be able to filter the packets passing over
      PPP interfaces.  This allows you to control which packets count as
      activity (i.e. which packets will reset the idle timer or bring up
      a demand-dialed link) and which packets are to be dropped entirely.
      You need to say Y here if you wish to use the pass-filter and
      active-filter options to pppd.

      If unsure, say N.

config PPP_ASYNC
    tristate "PPP support for async serial ports"
    depends on PPP
    select CRC_CCITT
    ---help---
      Say Y (or M) here if you want to be able to use PPP over standard
      asynchronous serial ports, such as COM1 or COM2 on a PC.  If you use
      a modem (not a synchronous or ISDN modem) to contact your ISP, you
      need this option.

      To compile this driver as a module, choose M here.

      If unsure, say Y.

config PPP_SYNC_TTY
    tristate "PPP support for sync tty ports"
    depends on PPP
    help
      Say Y (or M) here if you want to be able to use PPP over synchronous
      (HDLC) tty devices, such as the SyncLink adapter. These devices
      are often used for high-speed leased lines like T1/E1.

      To compile this driver as a module, choose M here.

config PPP_DEFLATE
    tristate "PPP Deflate compression"
    depends on PPP
    select ZLIB_INFLATE
    select ZLIB_DEFLATE
    ---help---
      Support for the Deflate compression method for PPP, which uses the
      Deflate algorithm (the same algorithm that gzip uses) to compress
      each PPP packet before it is sent over the wire.  The machine at the
      other end of the PPP link (usually your ISP) has to support the
      Deflate compression method as well for this to be useful.  Even if
      they don't support it, it is safe to say Y here.

      To compile this driver as a module, choose M here.

config PPP_BSDCOMP
    tristate "PPP BSD-Compress compression"
    depends on PPP
    ---help---
      Support for the BSD-Compress compression method for PPP, which uses
      the LZW compression method to compress each PPP packet before it is
      sent over the wire. The machine at the other end of the PPP link
      (usually your ISP) has to support the BSD-Compress compression
      method as well for this to be useful. Even if they don't support it,
      it is safe to say Y here.

      The PPP Deflate compression method ("PPP Deflate compression",
      above) is preferable to BSD-Compress, because it compresses better
      and is patent-free.

      Note that the BSD compression code will always be compiled as a
      module; it is called bsd_comp and will show up in the directory
      modules once you have said "make modules". If unsure, say N.

config PPP_MPPE
       tristate "PPP MPPE compression (encryption) (EXPERIMENTAL)"
       depends on PPP && EXPERIMENTAL
       select CRYPTO
       select CRYPTO_SHA1
       select CRYPTO_ARC4
       select CRYPTO_ECB
       ---help---
         Support for the MPPE Encryption protocol, as employed by the
     Microsoft Point-to-Point Tunneling Protocol.

     See http://pptpclient.sourceforge.net/ for information on
     configuring PPTP clients and servers to utilize this method.

config PPPOE
    tristate "PPP over Ethernet (EXPERIMENTAL)"
    depends on EXPERIMENTAL && PPP
    help
      Support for PPP over Ethernet.

      This driver requires the latest version of pppd from the CVS
      repository at cvs.samba.org.  Alternatively, see the
      RoaringPenguin package (<http://www.roaringpenguin.com/pppoe>)
      which contains instruction on how to use this driver (under
      the heading "Kernel mode PPPoE").

config PPPOATM
    tristate "PPP over ATM"
    depends on ATM && PPP
    help
      Support PPP (Point to Point Protocol) encapsulated in ATM frames.
      This implementation does not yet comply with section 8 of RFC2364,
      which can lead to bad results if the ATM peer loses state and
      changes its encapsulation unilaterally.

config PPPOL2TP
    tristate "PPP over L2TP (EXPERIMENTAL)"
    depends on EXPERIMENTAL && PPP && INET
    help
      Support for PPP-over-L2TP socket family. L2TP is a protocol
      used by ISPs and enterprises to tunnel PPP traffic over UDP
      tunnels. L2TP is replacing PPTP for VPN uses.

      This kernel component handles only L2TP data packets: a
      userland daemon handles L2TP the control protocol (tunnel
      and session setup). One such daemon is OpenL2TP
      (http://openl2tp.sourceforge.net/).

config SLIP
    tristate "SLIP (serial line) support"
    ---help---
      Say Y if you intend to use SLIP or CSLIP (compressed SLIP) to
      connect to your Internet service provider or to connect to some
      other local Unix box or if you want to configure your Linux box as a
      Slip/CSlip server for other people to dial in. SLIP (Serial Line
      Internet Protocol) is a protocol used to send Internet traffic over
      serial connections such as telephone lines or null modem cables;
      nowadays, the protocol PPP is more commonly used for this same
      purpose.

      Normally, your access provider has to support SLIP in order for you
      to be able to use it, but there is now a SLIP emulator called SLiRP
      around (available from
      <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which
      allows you to use SLIP over a regular dial up shell connection. If
      you plan to use SLiRP, make sure to say Y to CSLIP, below. The
      NET-3-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>, explains how to
      configure SLIP. Note that you don't need this option if you just
      want to run term (term is a program which gives you almost full
      Internet connectivity if you have a regular dial up shell account on
      some Internet connected Unix computer. Read
      <http://www.bart.nl/~patrickr/term-howto/Term-HOWTO.html>). SLIP
      support will enlarge your kernel by about 4 KB. If unsure, say N.

      To compile this driver as a module, choose M here. The module
      will be called slip.

config SLIP_COMPRESSED
    bool "CSLIP compressed headers"
    depends on SLIP
    select SLHC
    ---help---
      This protocol is faster than SLIP because it uses compression on the
      TCP/IP headers (not on the data itself), but it has to be supported
      on both ends. Ask your access provider if you are not sure and
      answer Y, just in case. You will still be able to use plain SLIP. If
      you plan to use SLiRP, the SLIP emulator (available from
      <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which
      allows you to use SLIP over a regular dial up shell connection, you
      definitely want to say Y here. The NET-3-HOWTO, available from
      <http://www.tldp.org/docs.html#howto>, explains how to configure
      CSLIP. This won't enlarge your kernel.

config SLHC
    tristate
    help
      This option enables Van Jacobsen serial line header compression
      routines.

config SLIP_SMART
    bool "Keepalive and linefill"
    depends on SLIP
    help
      Adds additional capabilities to the SLIP driver to support the
      RELCOM line fill and keepalive monitoring. Ideal on poor quality
      analogue lines.

config SLIP_MODE_SLIP6
    bool "Six bit SLIP encapsulation"
    depends on SLIP
    help
      Just occasionally you may need to run IP over hostile serial
      networks that don't pass all control characters or are only seven
      bit. Saying Y here adds an extra mode you can use with SLIP:
      "slip6". In this mode, SLIP will only send normal ASCII symbols over
      the serial device. Naturally, this has to be supported at the other
      end of the link as well. It's good enough, for example, to run IP
      over the async ports of a Camtec JNT Pad. If unsure, say N.

config NET_FC
    bool "Fibre Channel driver support"
    depends on SCSI && PCI
    help
      Fibre Channel is a high speed serial protocol mainly used to connect
      large storage devices to the computer; it is compatible with and
      intended to replace SCSI.

      If you intend to use Fibre Channel, you need to have a Fibre channel
      adaptor card in your computer; say Y here and to the driver for your
      adaptor below. You also should have said Y to "SCSI support" and
      "SCSI generic support".

config NETCONSOLE
    tristate "Network console logging support (EXPERIMENTAL)"
    depends on EXPERIMENTAL
    ---help---
    If you want to log kernel messages over the network, enable this.
    See <file:Documentation/networking/netconsole.txt> for details.

config NETCONSOLE_DYNAMIC
    bool "Dynamic reconfiguration of logging targets (EXPERIMENTAL)"
    depends on NETCONSOLE && SYSFS && EXPERIMENTAL
    select CONFIGFS_FS
    help
      This option enables the ability to dynamically reconfigure target
      parameters (interface, IP addresses, port numbers, MAC addresses)
      at runtime through a userspace interface exported using configfs.
      See <file:Documentation/networking/netconsole.txt> for details.

config NETPOLL
    def_bool NETCONSOLE

config NETPOLL_TRAP
    bool "Netpoll traffic trapping"
    default n
    depends on NETPOLL

config NET_POLL_CONTROLLER
    def_bool NETPOLL

config VIRTIO_NET
    tristate "Virtio network driver (EXPERIMENTAL)"
    depends on EXPERIMENTAL && VIRTIO
    ---help---
      This is the virtual network driver for virtio.  It can be used with
          lguest or QEMU based VMMs (like KVM or Xen).  Say Y or M.

endif # NETDEVICES